Plug the AC power cord into the power supply until it stops. Page 9 Your Console and Controller on To turn your console and controller on, press and hold the Xbox Guide button on your controller.
To turn on just your console, touch the console power button lightly. Plug the headset connector into the controller expansion port. Put on your headset and adjust the microphone position. Page Play Discs CDs. For information and instructions, visit Xbox news, movies, TV shows, and more. Connect devices and other portable supported, and you cannot play some Page 17 Xbox Dashboard system settings. Page 18 Listed as a Storage device Damaged hard drives might not show up in the Xbox Guide and could harm your Xbox If your hard drive is not listed as a storage console.
Hard drives that have been device, try the following, starting with the crushed, immersed in liquids, or exposed to first. Make sure that no objects are inserted into ventilation openings. Page Play Healthy Some unapproved third-party headsets including medical and physical conditions, may produce higher sound levels than stress and how one copes with it, overall approved Xbox Headsets.
Page Limited Warranty Colombia. Instead, it is your responsibility to hand this over to an applicable collection point for the recycling of batteries and electrical and electronic equipment. Page Copyright Microsoft, the furnishing of this document does not give you any license to these patents, trademarks, copyrights, or other intellectual property.
All rights reserved. I had to take matters into my own hands when it came to the PCEngine, and the results of this crazy note-taking and painstaking trial and error are below for your enjoyment. Even the SuperGrafx uses them, albeit with an extra new trick or two thrown in…. Show pagesource. Old revisions. Recent Changes. Table of Contents Console Schematics. And maybe other consoles as well.
Add 'em if you got 'em. Atari Field Service Manual. Cartridge pinout. TIA Schematic. Atari Jaguar Schematic Full. Atari Jaguar Schematic. Atari Lynx Schematic.
Fairchild Channel-F Schematic Page Memory expansion pinout. Commodore 64 Schematics. User port pinout. Expansion port. Expansion bus. Diagnostic slot. Expansion slot. Amiga CD32 Schematics. TurboGrafx Schematic 1 - Hu Circuit. TurboGrafx Schematic 2 - Hu Circuit. TurboGrafx Schematic 3 - Hu Circuit. TurboGrafx Schematic 4 - Power Input. Page 35 Another common point of failure is the little nub on the white actuator circled in green on the right, that little baby needs to fit into the trough on the bottom of the tray outlined in green in the next photo.
Also note the teeth on the far left of the actuator, it looks like there are some missing right? No, that's normal. Page 37 To completely remove the tray, lift the catch on the right side of the drive. Now you should have a good view of the laser assembly note that on the Phillips drive there is a black gear rail that sometimes pops out of place and the drive begins showing Disc is Dirty or Damaged errors.
Page 38 Flip the drive over to remove the bottom cover. Note the black tabs that are circled, these often bind and make the tray difficult to remove. Push those in first then remove the tray. Now we should have a good view of the bottom PCB, note the screws circled in green, these must be removed only for total disassembly, and if you are installing a new laser it is not necessary to remove the screws. Page 39 Now all the cables have been detached Take the end of the circuit board near the rear of the drive and flip it toward the front, this will reveal one more cord to detach.
Page 39 of Page 40 Now the laser assembly is exposed from the bottom of the drive. As well as the top If you wanted to try cleaning the lens and mirror this would be as far as you need to go. Blast the optics with compressed air attempting to direct the dust away from the lens top and mirror bottom Use a clean Q-tip and lens cleaner to clean the optics, you want to achieve a streak free surface. Page 41 Push them in the direction of the arrows and they will pop out and the laser assembly can be removed Now you should have a pile of parts that looks something like this Reassembly is the reverse.
Install the laser by pushing the rubber dampeners into their sockets. Connect the circuit board to the white four wire connector on the chassis, lay the circuit board over the chassis and install the four black screws. Page 43 Removing the solder is best accomplished by wiping a clean 15Watt or other low temperature soldering iron across the pads, be very careful!!!
Remove four Phillips 1 screws One of them is under the warranty void if seal damaged sticker Remove the top cover. Page 45 The rail is held in place by a small metal spring loaded tab. The metal is in the shape of a number seven 7 the small leg presses against the plastic and holds the rail from escaping; to remove we need to elevate the metal tab over the plastic so it can slide to the left. Page 46 Getting the tab over the plastic is a two handed operation. I used two small regular precision screw drivers to lift and one to leverage to the side.
In this photo you can see the tab is lifted over the plastic riser, and held in place by a screw driver, the rail can now be lifted up. In this photo the rail has been freed but the front is still attached, pulling the rail about a quarter inch back releases the front.
Page 47 Now that the gear and rail has been swapped over to the new laser it is time to re-install the laser and rail. Start by fitting the laser U shaped notch back into the lower rail in this photo. Next insert the top rail into the standoff at the top right in this picture. Page 48 Using a precision screw driver, depress the tab so it is below the plastic, you may want to also replace the glue that holds the metal in its place.
Reassemble and install in your Xbox! Page 48 of The top and bottom covers come off easily To slide out the tray either use the emergency eject from the front of the drive or flip it over and slide this white thing in the direction of the arrow. Page 50 Removing the DVD tray, two clips need to be depressed on either side of the front of the DVD to allow its removal If you are having tray eject issues the nub on the white thing circled below has most likely jumped out of the trough it fits in on the bottom of the tray, when reassembling the tray be sure this fits back into the trough on the bottom of the tray Removing the laser assembly, remove the two screws where the blue circle is in this photo Page 51 This is a view of the bottom of the drive and you can see the grommet on the right has been removed from its "C" shaped holder.
The grommet on the left still needs to come out! With the laser loose I find this is a good time to remove the circuit board to gain easy access to the ribbon cables. Page 52 Re-assembly - Install the laser assembly back into the chassis, put the shaft of a small screwdriver through the hole in the center of the rubber grommet and push it into place Note the large headed screws on the left in this picture have been installed Lay the PCB on top of the chassis and reconnect two ribbon cables Page 52 of Page 53 The PCB is held in place by two back plastic clips circled below, press the board into place Flip the drive into the upright position.
On the top, install the ribbon cable that attaches to the laser. Page 55 For the purposes of this tutorial I have removed the ribbon cables to get better shots of the laser, this is not necessary for adjusting the pot Looking at the Pot we see 3 contacts.
Position the drive so the single contact is on your left, the one to measure from on the right is the lower one. Page 56 Touch points 1 and 3 with the probes, you use red or black with either it makes no difference. Get an initial reading, it should be over and not fluctuate. Scrape away the epoxy on the screw, not always an easy task and probably the most likely chance to irreparably damage your DVD.
The bigger paperclips work best. Straighten it out as below. You will find a hole on all Xbox consoles at Arrow 1. Page 58 Once it is out far enough the tray can be pulled out easily, never force it Page 58 of Here is what they mean.
Disclaimer: This information is a believed to be correct, should be as close as it gets; If you have an Xbox with bad Hard Drive the process to swap gets a bit more complicated and there is no possibility of doing this without installing a modchip. Page 63 That's all. You can now recover those memories, once thought lost, from your locked hard drive.
Remember, when booting your XBOX only the locked hard drive you were trying to recover will boot. Any other hard drive will need to be unlocked to boot up. Page 64 Xbox apps to easily unlock a drive with 1 button click. ConfigMagic can unlock harddrives, but also newer versions of EvolutionX dashboards and also all 4th generation modchip OS'. Page 66 Extracting the HD password from an Xbox hard drive The Xbox harddrive uses a fairly old but relatively unused set of security commands to prevent easy access to it's built in drive.
You will see if you are watching the DIOR line that the Xbox is polling that register waiting for the bit to clear. When it does the Xbox will begin transferring the data bytes to the drive.
Page 68 DIOW line changes, but should be able to see all of the actual data bus changes. If you decide to try this, verify it works on some other drive before using your Xbox drive, as I have no idea what kinds of problems might come up if it fails.
Page 69 Error Code When Error Code 21 comes up power off the Xbox, unplug the Xbox 1's hard drive and put it back into Xbox 1. Reconnect all the cable to Xbox 1's hard drive and boot it. It should boot fine.
0コメント